Feeling a cold draught near a window or door is one of the most noticeable signs of winter in an older home. It makes rooms feel colder, pushes up heating costs and can let in noise and dust. The good news is that draughts around uPVC windows and doors can often be fixed with an adjustment or a repair, without replacing the whole unit.
How to find where the draught is coming from
On a windy day, slowly move the back of your hand around the edges of the window or door. You can also use a lit candle or incense stick, held safely away from curtains, and watch where the smoke moves. Check:
- Around the opening sash or door, where it meets the frame
- At the corners, especially at the bottom
- Where the frame meets the wall, inside and outside
- Around letterboxes, keyholes and cat flaps on doors
Common causes and fixes
1. Worn or flattened seals
uPVC windows and doors use rubber gaskets to seal the gap between the opening part and the frame. Over the years, these gaskets can flatten, shrink, crack or come away from their groove. The fix is usually straightforward: the old gaskets are pulled out and new ones fitted.
2. Dropped sash or door
Hinges wear over time, and heavy opening sashes and doors can gradually drop. When this happens, the door or window no longer sits evenly against the seals, leaving a gap on one side. You might also notice the door catching on the frame or the handle becoming stiff. Most modern hinges can be adjusted, and worn hinges can be replaced.
3. Keeps and locking points out of adjustment
The locking points on the sash or door pull it tight against the seals when locked. If the keeps on the frame are out of position, the door or window will not close tightly. Adjusting the keeps, or the cams on the locking mechanism, often solves the problem.
4. Worn friction hinges on windows
Opening windows sit on friction hinges that wear with use. Worn hinges can stop the sash closing squarely, leaving a gap at the top or bottom. Replacing the hinges restores a proper seal.
5. Failed seals around the frame
The gap between the window or door frame and the wall is sealed with silicone or another sealant outside, and often trims inside. Old sealant cracks and shrinks, letting draughts and water in. It can be cut out and replaced.
6. Gaps around letterboxes and keyholes
Letterboxes are a common source of draughts on front doors. Fitting a letterbox with brush seals or an internal flap helps, as do keyhole covers.
7. Threshold and bottom seals
The bottom of a door is often where draughts are worst. Worn threshold seals or weather bars can be replaced, and a dropped door can be adjusted so the bottom seal makes proper contact.
When replacement makes more sense
Repairs are not always the best value. Replacement may be the better choice if:
- The frames are warped, cracked or damaged
- The double-glazed units have failed and the frames are also old
- Parts are no longer available for the hinges or locks
- Several windows or doors are all suffering from the same problems
- The windows are single glazed or very old double glazing
Our article on when to repair or replace a window goes into this in more detail.
Quick fixes you can try yourself
- Clean and lubricate hinges and locking mechanisms with a suitable spray, following the manufacturer’s guidance.
- Check that trickle vents close properly if you want to reduce airflow, but remember they are there for ventilation.
- Use a draught excluder at the bottom of internal doors.
- Fit heavy curtains or thermal blinds on draughty windows as a short-term measure.
Avoid sealing opening windows shut, covering trickle vents or blocking air bricks. Homes still need some ventilation to prevent condensation and damp, as explained in our article on condensation on windows.
Why regular maintenance helps
A few minutes of care each year keeps uPVC windows and doors sealing properly for longer. Wipe the frames and seals with warm soapy water, clear dirt and debris from the tracks and drainage slots at the bottom of the frame, and lightly lubricate hinges, locking points and handles. Avoid harsh solvents, which can damage seals and frames. If a window or door starts to feel stiff or needs extra force to lock, get it adjusted early. Small adjustments now can prevent worn parts, broken mechanisms and draughts later.
Frequently asked questions
Can I replace window seals myself?
It is possible on some windows, but getting the right gasket profile and fitting it correctly makes a big difference. A window repair specialist can supply and fit the correct seals.
Why is my door draughty only in winter?
uPVC expands and contracts with temperature. In cold weather, small gaps can open up, especially if the door is already slightly out of adjustment.
Will new windows stop all draughts?
Properly fitted modern windows and doors should be draught-free when closed and locked. Trickle vents still provide controlled background ventilation, which is different from an uncontrolled draught.
Window and door repairs in Bolton
Luxe Windows carries out window and door repairs, including seals, hinges and locks, as well as new uPVC windows and doors across Bolton, Horwich, Kearsley, Little Lever and the North West. Call 01204 929995 for help.